3D Printer - Revision history

Nicolas: /* Network */

2025-10-11T06:22:57Z

Network

← Older revision		Revision as of 06:22, 11 October 2025
Line 325:		Line 325:
	Environment="HOST=0.0.0.0"		Environment="HOST=0.0.0.0"
	Environment="PORT=5000"		Environment="PORT=5000"
			</pre>

			==== Camera ====
			* Install webcamd and ffmpeg
			<pre>
			apt-get install webcamd ffmpeg
	</pre>		</pre>

2025-10-11T06:20:28Z

Network

← Older revision		Revision as of 06:20, 11 October 2025
Line 328:		Line 328:

	* Change Webcam listner to 0.0.0.0 #		* Change Webcam listner to 0.0.0.0 #
	** Add the following into /boot/octopi.txt		** Add the following into /boot/firmware/octopi.txt
	<pre>		<pre>
	camera_http_options="-n --listen 0.0.0.0"		camera_http_options="-n --listen 0.0.0.0"

2025-10-11T02:10:09Z

Network

← Older revision		Revision as of 02:10, 11 October 2025
Line 317:		Line 317:
	* Disable haproxy (no need as using Apache2 proxy)		* Disable haproxy (no need as using Apache2 proxy)
	<pre>		<pre>
	~~systemclt~~ disable haproxy		systemctl disable haproxy
	</pre>		</pre>
	* Setup octoprint python program for listening 0.0.0.0		* Setup octoprint python program for listening 0.0.0.0

2022-06-25T22:18:09Z

OctoPrint

← Older revision		Revision as of 22:18, 25 June 2022
Line 428:		Line 428:
	sudo perl Build.PL		sudo perl Build.PL
	echo "If everything was installed properly,you should be able to run Slic3r with the command ./slic3r.pl"		echo "If everything was installed properly,you should be able to run Slic3r with the command ./slic3r.pl"
			</pre>


			====Disable under power warning ====
			* edit /boot/config.txt and add the following lines at the end
			<pre>
			#Disable under voltage warnings
			avoid_warnings=1
			avoid_warnings=2
	</pre>		</pre>

2021-11-11T04:55:23Z

Network

← Older revision		Revision as of 04:55, 11 November 2021
Line 315:		Line 315:
	==== Network ====		==== Network ====

	* Disable haproxy ~~and change listner to 0.0.0.0~~		* Disable haproxy (no need as using Apache2 proxy)
	<pre>		<pre>
	systemclt disable haproxy		systemclt disable haproxy
	</pre>		</pre>
	* Setup octoprint for listening 0.0.0.0		* Setup octoprint python program for listening 0.0.0.0
			** Update the address in /etc/systemd/system/octoprint.service
	<pre>		<pre>
	~~vi /etc/systemd/system/octoprint~~.~~service~~		[Service]
			Environment="HOST=0.0.0.0"
			Environment="PORT=5000"
	</pre>		</pre>

	* Change Webcam listner to 0.0.0.0		* Change Webcam listner to 0.0.0.0 #
	** Add the following into /boot/octopi.txt		** Add the following into /boot/octopi.txt
	<pre>		<pre>

2021-11-11T04:51:43Z

Network

← Older revision		Revision as of 04:51, 11 November 2021
Line 315:		Line 315:
	==== Network ====		==== Network ====

	* Disable haproxy		* Disable haproxy and change listner to 0.0.0.0
	<pre>		<pre>
	systemclt disable haproxy		systemclt disable haproxy
Line 323:		Line 323:
	vi /etc/systemd/system/octoprint.service		vi /etc/systemd/system/octoprint.service
	</pre>		</pre>

			* Change Webcam listner to 0.0.0.0
			** Add the following into /boot/octopi.txt
			<pre>
			camera_http_options="-n --listen 0.0.0.0"
			</pre>

	====Switch On/Off====		====Switch On/Off====
	* In /etc/init.d/octoprint, add the following before RETVAL="$?"		* In /etc/init.d/octoprint, add the following before RETVAL="$?"

2021-11-11T04:27:40Z

← Older revision		Revision as of 04:27, 11 November 2021
Line 307:		Line 307:

	===OctoPrint===		===OctoPrint===

			==== Alias ll ====
			<pre>
			sed -i -e '$ a alias ll="ls -alF"' /etc/bash.bashrc
			</pre>

	==== Network ====		==== Network ====

2021-11-11T04:16:23Z

← Older revision		Revision as of 04:16, 11 November 2021
Line 352:		Line 352:
	confirm: true		confirm: true
	name: Stop video stream		name: Stop video stream
			</pre>

			* Add pi execution without password in /etc/sudoers
			<pre>
			pi ALL=(ALL) NOPASSWD: ALL
			or
			pi ALL=(ALL) NOPASSWD: /bin/systemctl
	</pre>		</pre>

2021-11-11T04:06:46Z

Gcode

2021-11-10T04:53:21Z

Slic3r

@@ Line 385: / Line 385: @@
 * Configuration file
 ** Cura 15 configuration file [[File:Configuration_file_for_Cura-15.04.ini]]
 ===Gcode===